Sep 05

Cookbook: set-up a TFTP server on Ubuntu

Reading time: 1 – 2 minutes

Sometimes TFTP is the only protocol available to exchange files with an embedded system. So, it’s very easy to have that supported in our workstation or any other place to exchange files with those systems.

Set up steps:

apt-get install tftpd-hpa

modify file “/etc/default/tftpd-hpa”:

TFTP_OPTIONS="--secure --create"

–secure: Change root directory on startup. This means the remote host does not need to pass along the directory as part of the transfer, and may add security. When –secure is specified, exactly one directory should be specified on the command line. The use of this option is recommended for security as well as compatibility with some boot ROMs which cannot be easily made to include a directory name in its request.

–create Allow new files to be created. By default, tftpd will only allow upload of files that already exist. Files are created with default permissions allowing anyone to read or write them, unless the –permissive or –umask options are specified.

Needed to allow uploads in that directory:

chown -R tftp /var/lib/tftpboot

Restart and check if the service is running:

service tftpd-hpa restart
service tftpd-hpa status
netstat -a | grep tftp
Sep 01

New home server working as a wifi AP and DHCP server

Reading time: 2 – 3 minutes

At the beginning of August I’ve received a new home server, I decided to stop my old HP ML110 G5 and substitute that by a new silent and low power server also based on Intel technologies in this case it’s al i5 with 8G of RAM and 128GB of SSD for less than 300€ including custom costs I think it’s a very good investment.



I installed Ubuntu 16.04 LTS server, I don’t tried de Win10 pre-installed. I happy to see a very new and powerful BIOS with tons of options. But in this blog entry I want to explain how to set-up the wifi card as a wifi AP. I didn’t have to do anything to configure the card. It worked by default.

Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe

The first thing is check if the wifi network is compatible with the AP mode.

iw list
Supported interface modes:
         * IBSS
         * managed
         * AP
         * AP/VLAN
         * monitor
         * mesh point

Next thing is install the “hostapd” which is going to take care to set-up the AP. The configuration file have to be something like that “/etc/hostapd/hostpad.conf

interface=wlan0   # change that with the wifi interface name
ssid=test         # your wifi network name
channel=1         # look up for a free channel
wpa_passphrase=1234567890   # passwor to join the wifi network

Modify “/etc/default/hostapd” and put that:


Start the hostapd service:

sudo service hostapd start

Now the AP is running but a DHCP service giving IPs it’s need, I used “isc-dhcp-server”. First thing to configure is “/etc/default/isc-dhcp-server” with the wireless network name:


Next file to be configured is “/etc/dhcp/dhcpd.conf”:

ddns-update-style none;
log-facility local7;

subnet netmask {
    option domain-name-servers;
    option routers;

Don’t forget to start the service:

sudo service isc-dhcp-server start

If it’s needed remember to create the proper iptables rules and enable “ip_forward” in /proc filesystem. I’m not going to describe that because in my case it’s not going to be useful.

This is not a specially interesting post entry but useful as a reference, when you have to use a fast and easy cookbook to setup a wifi AP.

Aug 29

Internet fail over connection with Mikrotik

Reading time: 2 – 4 minutes

Based on my home configuration I’m going to describe how to set up a Mikrotik to manage fail over Internet connection. Next schema describes a Mikrotik gateway with two internet connections (GUIFI and SS). Assuming GUIFI as a default Internet connection periodic checks on Google DNSes ( and will allow to know when it’s good to change the default route.


If you have some Linux routing background it will be easier to understand the configuration. Main idea is use policy routing tables and mark packets to use one table or other. In my case I have two routing tables GUIFI and SS, and of course, the default gateway of each of those tables is the gateway indicated in the schema.

First step is take care about the routes for hosts to monitor; using GUIFI connection will be checking connectivity to and using SS the monitored host will be

/ip route
add dst-address= gateway= scope=10
add dst-address= gateway= scope=10

Second step is configure two routing tables, those routes will check Internet hosts availability. Routes are resolved recursively (more info), and will be active only if any host is pingable.

# routing table for GUIFI
/ip route
add distance=1 gateway= routing-mark=GUIFI check-gateway=ping
add distance=2 gateway= routing-mark=GUIFI check-gateway=ping
# routing table for SS
/ip route
add distance=1 gateway= routing-mark=SS check-gateway=ping
add distance=2 gateway= routing-mark=SS check-gateway=ping

Routing table looks like that:


Next step will be create marking rules in the firewall:

# next rule mark all LAN traffic ( before routing
# it'll be processed by routing table GUIFI
# it makes GUIFI the default Internet connection 
/ip firewall mangle
add action=mark-routing chain=prerouting comment="All LAN traffic" dst-address=\
    ! new-routing-mark=GUIFI passthrough=no src-address=

If any specific host, service or whatever want to use specific routing table, then you can create new rules with proper mark to redirect the traffic to that Internet connection. But if that path fails other Internet connection will be used.

In my case I have a more complicated scenario, internal VoIP server uses a IP Telephony service only available through GUIFI connection. The way to force that is forbidding traffic to SS connection. A simple firewall rule will help to do that:

# X.X.X.X = IP address of the IP telephony provider
/ip firewall filter
add action=reject chain=forward dst-address=X.X.X.X in-interface=\
    bridge-lan out-interface=SS-eth2

I hope previous simple notes are useful for you, they are inspired by Advanced Routing Failover without Scripting.

Aug 22

OpenVPN between pfSense and Mikrotik

Reading time: 3 – 5 minutes

vpn-pfsense-mikrotik-schemaAssuming previous scenario I’m going to describe the required configurations on pfSense and Mikrotik. Certifcate creation is not part of the scope of this document, if you are not familiar about how to do that it’s a good idea to use the pfSense certificate manager to do it. My last advice is take care with certificates 90% of problems that I found in my life when I was working on VPNs are because of that. Take your time to check it before spend your time playing with other configurations.

In that scenario pfSense will play the role of the VPN server and Mikrotik will be the client, so I’m going to start describing pfSense configurations.

Create OpenVPN server on proper section:



Important things to take in account when you set up the parameters are socket has to be a TCP socket in my case I decided to use port 1201:

pfsense-openvpn-server-configNext settings on the same place are about local network and tunnel IP addresses, this is required to create proper routing rules on the server and the client.



Last part to configure on this sections is extremly simple, only take care to unmark everything and check “address pool” setting.



Remember to open that port on Firewall rules.



A VPN user is required to authenticate the process, just go to “User Management” inside the “System” menu:



pfSense is configured, now it’s time to set-up the OpenVPN client on Mikrotik using Winbox. Remember to import the certificates:



Click on “PPP” this on the left menu:



Add an OVPN Client connection using the “+” button, the parameters for that connection are:



Another required thing to define on “PPP” is the profile, click on the tab “Profile” and using the button with symbol “+” create a new profile like that:



Everything is ready, now it’s time to check if the connection is OK. First go to the OVPN client on Mikrotik, remember this is on “PPP” menu option and inside tab “Interfaces”. Clicking on the interface you’ll see the status details. If it’s disconnect going to pfSense or Mikrotik logs you can see the negotiation details.

Remember usually the problem is with your certificates, but first of all you have to ensure that the negotiation tries to start.

Enjoy it and good luck.


Aug 15

Sniffing on Mikrotik and streaming in real-time to Wireshark

Reading time: 2 – 2 minutes

When you have a Mikrotik in any point of your network and you want to launch a sniffer for debugging or troubleshooting, a part from original RouterOS tools, you can stream captured traffic in real-time to Wireshark and inspect packets there.

The idea is exactly the same like I explained on the entry: Sniffing traffic in a Linux box and streaming in real-time to Wireshark on Windows.

Mikrotik configuration using the web interface is like that:


We assume is the IP address of the Wireshark box, ensure that you don’t block UDP traffic on port 37008 because the stream from Mikrotik uses that target port. And define your own filters.

About Wireshark configuration is really simple, just set up the filter to allow only traffic from sniffing stream and select the network interface where traffic comes.


Previous captures allow us to debug DNS queries to Google DNS service, this is the result when you click to the icon marked with a red circle on previous screen capture.


Aug 08

Setting alternative getty service on Ubuntu with systemd

Reading time: 2 – 2 minutes

There is an a curses app called wicd-curses which uses a service called wicd, thanks to that app is possible to setup networking configuration for wired and wireless networks using a ncurses environment.

The purpose of the next cookbook is get the wicd-curses running on tty1 after the Ubuntu boots; allowing a console user configure networking settings without login in the system. After installing the wicd-curses package we have the daemon running. The first thing to do is ensure that systemd is taking take of the service:

systemctl enable wicd.service

Next we have to stop the service that launch getty on tty1 when the system boots:

systemctl disable getty@tty1.service

Now it’s time to define configuration file for our service /etc/systemd/system/wicd-boot.service:

Description=WICD ncurses on tty



Finally enable wicd-boot.service is required:

systemctl enable wicd-boot.service

Try new configuration is possible without reboot just doing:

systemctl daemon-reload
systemctl restart wicd-boot.service
# check if the service is running with
systemctl status wicd-boot.service

On other tty consoles we also have getty but not in tty1 where we have the wicd-curses interface. When we reboot the system we have the same behavior. Before finish the email I want to mention two helping references:

Aug 01

Extracting private and public keys from a p12 file

Reading time: 1 – 2 minutes

PKCS#12 is a container for storing many cryptography objects as a single file. It is commonly used to bundle a private key with its X.509 certificate or to bundle all the members of a chain of trust. This is a fast and simple summary about how to extract your keys from those kind of files:

#Private key:
openssl pkcs12 -in file_name.p12 -nocerts -out private.key
openssl pkcs12 -in file_name.p12 -clcerts -nokeys -out public.crt

Recurrently I have to access to a usuful guide about those kind of openssl parameters, let me refer that guide:

The Most Common OpenSSL Commands (local copy)

Update 2016/09/19
Usefull links for SSL:

Jul 31

Avui fa 16 anys que vaig començar a escriure el blog

Reading time: 1 – 2 minutes



Feliç de recordar l’efemèride i de malgrat no tenir un blog molt prolífic poder explicar que he aconseguir mantenir l’hàbit d’anar compartint encara que fos en petites píldores alguns dels fets i coneixements que la vida m’ha anat permetent disfrutar. Des de l’arribada del Roc més que mai he hagut de tancar el meu “pipeline” de projectes però una cosa positiva és que t’acabes centrant en l’escència i en el que et fa disfrutar més. Per desgràcia no pots atendre moltes altres coses que sovint tornen en forma de records o pensaments, això si, t’adones que les coses que has permès que seguissin al teu costat tenen el millor gust que mai havien tingut.

Només puc dir-vos que la meva intenció és seguir buscant reconets i estones per seguir compartint-vos el que hem passa pel cap, mentrestant ús envio una abraçada molt forta.


Jul 27

Mikrotik as a PPTP server for Android

Reading time: 4 – 6 minutes

Two years ago I installed a Mikrotik Cloud Switch and lately I stoped my pfSense and I started using that switch as my network router, firewall and also as a switch. RouterOS is really powerful and allows to do a lot of things with that hardware. One of those things is set-up a VPN server based on PPTP. This is not the most secure way to create VPNs but usually the only requirement is a little bit of security on top of an IP over IP service that allows us to use local service when we’re in remote. In my case I have a lot of services in my LAN and I need some of them when I’m out of home specially I need to use them from my mobile phone.

Next steps describe how I set-up a PPTP server on my Mikrotik server allowing my Android 6 device (Huawei Mate 8) to connect to my home services through the VPN. Bellow you have a simple schema representing the schenario of the solution:


I’m only going to describe steps from the web console, of course, all those steps can be done using Winbox or the command line. To be honest I’m not used to RouterOS CLI but I think it’s not difficult to figure out the CLI commands to get the same result.

First step is set-up a pool of IP addresses to be assigned to the tunnel endpoints.



Thanks to an ARP proxy those IP addresses will be available like local IPs, this is transparent for the VPN configuration.


configuration of connection profile is done inside “Profiles” tab:


first of all create a new profile called “default-encription”:


and another profile called “pptp-profile”:


“Secrets” tab is where you have to manage users, in my case only two users are created:


configuration details about my user are:


Inside PPP menu there is a button with a label “PPTP server” click there…


… and copy next settings:


Don’t forget to check that your PPTP port is accessible from your public IP address. Remember it’s 1723/TCP.

Android configuration is simple, first of all go to “settings” icon. Look for a “More” section bellow network options, and you’ll find VPN managment. Add a new connection, define a name, the type and the IP address and leave the rest by default. After that when you come back to VPN list you’ll find your new VPN in the list, click there and just set-up your PPTP credentials.


If you have some trouble the only thing that you can do is go to Mikrotik logs or start sniffing to figure out where is the problem. I had to do some tests before it was working but in the end everything was so simple like I explained here.

Good luck and enjoy it.

Thanks to next blog entries to inspire me:



Jun 06

Remove old kernels when there is no space in /boot

Reading time: 1 – 2 minutes

The first step is get some space in the partition “/boot” because without that it’s impossible to do anything.

So go to /boot and remove some “initrd” files as they are the biggest ones. A few of them will be enough.

After that a good point is to ensure there is no partial installation pending to finish:

apt-get -f install

Now it’s a good idea to purge all kernels except the running one:

dpkg -l 'linux-*' | sed '/^ii/!d;/'"$(uname -r | sed "s/\(.*\)-\([^0-9]\+\)/\1/")"'/d;s/^[^ ]* [^ ]* \([^ ]*\).*/\1/;/[0-9]/!d' | xargs sudo apt-get -y purge

To avoid that in future before filling the partition, it’s a good idea to install and run periodically: purge-old-kernels. Installation and example of use are:

# installation
apt-get install bikeshed
# keep three old kernels:
purge-old-kernels --keep 3
# if you want to put that in the crontab use that command
purge-old-kernels --keep 3 -qy

If you’re a Grub user don’t forget to run:


Personally I have a nightmare with that problem and Ubuntu, especially with version 12.04 which is installed in a lot of servers that I manage. I repeated the previous process a lot of times and in the end, I decided to document it because I always have to go to Google and find the proper steps to solve that problem.